Eight service tasks: from the fault report to the warranty claim.

You decide where AEDIL starts. All cases are examples.

The eight tasks

01 · Before anything fails

Early warning

“Something’s brewing.”

For
  • Head of service
  • Team lead and dispatch
Lifts · Door drive
  1. Incoming
    Telematics · 05:40A-17
    Door closing time 2.9 s. Three weeks ago 2.3 s.

    No alarm · Limit 3.5 s

  2. AEDIL
    Early warningSN 4410-0832
    Same pattern as before a door coupler failure.
    Compared
    12 drives of this series
    Lead time
    Failure usually after 4 to 6 weeks

    Swap it at the service visit on 12 Nov. The part is reserved.

  3. Result

    Coupler swapped at the service visit. The lift keeps running.

    • Falls: Unplanned downtime
02 · When the machine is down

Call logging

“Machine’s down.”

For
  • Service desk and back office
Machine tools · Machining centre
  1. Incoming
    Call · 06:12

    “Our machining centre in hall 2 is down. Alarm 2041.”

    Nameplate.jpg
  2. AEDIL
    Case 25-30411Created
    Serial no.
    18-0942 · read from the photo
    Fault
    2041 · Gripper not in end position
    Contract
    Service Plus · 8 h response

    Follow-up: is the gripper in its home position?

  3. Result

    A clean case in four minutes. The customer explains it once.

    • Falls: Time to a clean case
03 · When the machine is down

Remote diagnosis

“Does this need a call-out?”

For
  • Team lead and dispatch
  • Service desk and back office
  • Service technician
Refrigeration · CO₂ rack system
  1. Incoming
    Fault · 22:48Cold store 3
    High-pressure fault. The rack shuts down.
    Stored
    48 t of goods at −22 °C
  2. AEDIL
    Diagnosis · High pressure
    1. Fan curve off since parameter change on 21 OctFans run at 40% at night71%
    2. Condenser dirty19%
    3. High-pressure switch faulty10%

    Reset curve P-31, watch the high pressure for 30 minutes.

  3. Result

    Solved remotely in 25 minutes. No night call-out.

    • Rises: Remote resolution rate
04 · On the job

On-site troubleshooting

“I’m at the machine and I’m stuck.”

For
  • Service technician
  • Dealer
Robotics · Palletising cell
  1. Incoming
    Voice message · 10:05

    “Cell 4, axis 3 is throwing following error F-2307. Swap the motor?”

  2. AEDIL
    Troubleshooting · Axis 3

    Don’t swap it yet. Measure the brake voltage at X41:7, target 24 V.

    18 V.

    Check the brake cable at the drag chain entry. That’s where it breaks on this series.

  3. Result

    Cable replaced, motor stays in. The cell runs again after 1.2 hours.

    • Falls: MTTR
05 · On the job

Dealer network

“The dealer’s technician is at the machine.”

For
  • Dealer
  • Service desk and back office
Construction · Compact excavator
  1. Incoming
    Dealer 0417 · 14:20
    Left travel drive weak under load.
    Fault code
    7.12
    Machine
    Built 2023 · 1,140 h
  2. AEDIL
    Reply to dealer 0417
    Known from build C.
    Cause
    Flushing valve, left travel motor
    Part
    2207-410 · warranty

    Swap the flushing valve per SI 23-044. The warranty claim is ready.

  3. Result

    The dealer fixes it the same day, without calling the factory.

    • Rise: Cases the dealer solves alone
06 · After the job

Service report

“So what was it in the end?”

For
  • Service technician
  • Quality and engineering
Woodworking · Edgebander
  1. Incoming
    Voice note · 17:32

    “Glue pot wouldn’t reach temperature. Cartridge heater two had blown, swapped it. Test edge clean.”

  2. AEDIL
    Service report · 25-20981
    Finding
    Glue pot not reaching 190 °C
    Cause
    Cartridge heater 2 burnt out, controller switching 12 K late
    Action
    Cartridge replaced, controller readjusted
    Parts
    1 × cartridge heater 800 W

    Report ready for sign-off. The cause goes to field quality.

  3. Result

    Signed off in the evening, invoiced the next morning.

    • Rise: Complete reports
07 · After the job

Service overview

“Monday, 8 am: where’s the fire?”

For
  • Head of service
  • Team lead and dispatch
Printing · Installed base
  1. Incoming
    Week 45 · Monday 07:00
    Tickets
    214
    Reports
    61
    Escalations
    9
    Services due
    18

    From four systems · last week

  2. AEDIL
    Service overview · Week 4508:00
    • B-7 · Gripper shaft3 repeat visits
    • Customer 3318 · 4 visitsEscalation risk
    • Part 6610-02 · out of stock5 jobs

    Gripper shaft to product support. Call customer 3318 today.

  3. Result

    By 8:15 everyone knows who goes where.

    • Fall: Repeat visits
08 · After the job

Field quality

“Why does that part keep failing?”

For
  • Quality and engineering
  • Head of service
Pumps · Centrifugal pump
  1. Incoming
    Last 90 daysKP-80
    Failure pattern: mechanical seal leaking.
    Reports
    31
    Warranty claims
    12
    Returned parts
    9
    Countries
    4
  2. AEDIL
    Field failure analysis · KP-80
    Parts list
    Rev. F · EPDM elastomer instead of FKM

    Cluster since parts list rev. F. Open an 8D report.

  3. Result

    Within two weeks, engineering has the cause. Field campaign for 214 pumps.

    • Falls: Time to cause

AEDIL reads what your service already has.

How AEDIL works
Your cloud AEDIL reads
  • Tickets
  • Service reports
  • Fault codes
  • Wiring diagrams
  • Parts lists
  • Telematics
AI service engineer
AEDIL works in
  • ERP
  • CRM
  • Ticket system
  • Field service
  • Files

Bring your hardest case.

We’ll walk through it with you, like the cases on this page.

Book a call